Consider swapping the screw terminals for lever terminals #10

Open
opened 2026-11-16 11:38:15 +00:00 by Claude · 0 comments
Collaborator

Lever (spring clamp) terminals would suit a van better than screw terminals, but the swap means a new revision of the CAN node and the lighting node. This issue records what to weigh up before doing it.

The figures below are from memory and need checking against datasheets.

Why

  • Spring clamps keep their grip under vibration. Screw terminals can work loose over time.
  • Wiring needs no screwdriver, and stranded wire goes in without ferrules.

Cost

  • WAGO lever terminals (the 2601 series is the 3.5 mm one) are about 40–60p per pole. Each node has about 30 poles, so roughly £12–18 a board. The current Phoenix parts are about half that.
  • Chinese equivalents (Degson, KF series) are 5–15p per pole and LCSC stocks them. Lever quality varies, so buy a handful to try first.

Size

  • Depth: about 12–15 mm front to back, against 7.5 mm now. Each terminal row moves 5–7 mm inward, or the board grows by that much per side.
  • Height: about 9–10 mm closed, similar to now. The levers swing up to about 15 mm when open.
  • Pitch: 3.5 mm versions exist, so the row lengths can stay the same.

Current

  • The 3.5 mm lever types are rated about 10–12 A, which covers the 5 A light outputs and the I/O.
  • The lighting node's 20 A supply needs a bigger part, such as the WAGO 2604. That one is about 14 mm tall, so it would still pass through the case lid as J1 does now.

Work involved

  • New footprints for each terminal. Some would need drawing from the datasheet.
  • Both node boards re-placed and re-routed. The lighting node's scripted power copper has to be redone too.
  • All the cases redrawn. Openings, lettering and lid slots move, and the lid needs wide slots over every row for the open levers, or it comes off for wiring.
  • Assembly doesn't change. The parts are through-hole, so they are still hand-soldered or sourced separately.

Suggested timing

Not worth doing on its own before the first batch is built and tested. Fold it into the next board revision that happens for another reason.

Lever (spring clamp) terminals would suit a van better than screw terminals, but the swap means a new revision of the CAN node and the lighting node. This issue records what to weigh up before doing it. The figures below are from memory and need checking against datasheets. ## Why - Spring clamps keep their grip under vibration. Screw terminals can work loose over time. - Wiring needs no screwdriver, and stranded wire goes in without ferrules. ## Cost - WAGO lever terminals (the 2601 series is the 3.5 mm one) are about 40–60p per pole. Each node has about 30 poles, so roughly £12–18 a board. The current Phoenix parts are about half that. - Chinese equivalents (Degson, KF series) are 5–15p per pole and LCSC stocks them. Lever quality varies, so buy a handful to try first. ## Size - Depth: about 12–15 mm front to back, against 7.5 mm now. Each terminal row moves 5–7 mm inward, or the board grows by that much per side. - Height: about 9–10 mm closed, similar to now. The levers swing up to about 15 mm when open. - Pitch: 3.5 mm versions exist, so the row lengths can stay the same. ## Current - The 3.5 mm lever types are rated about 10–12 A, which covers the 5 A light outputs and the I/O. - The lighting node's 20 A supply needs a bigger part, such as the WAGO 2604. That one is about 14 mm tall, so it would still pass through the case lid as J1 does now. ## Work involved - New footprints for each terminal. Some would need drawing from the datasheet. - Both node boards re-placed and re-routed. The lighting node's scripted power copper has to be redone too. - All the cases redrawn. Openings, lettering and lid slots move, and the lid needs wide slots over every row for the open levers, or it comes off for wiring. - Assembly doesn't change. The parts are through-hole, so they are still hand-soldered or sourced separately. ## Suggested timing Not worth doing on its own before the first batch is built and tested. Fold it into the next board revision that happens for another reason.
Sign in to join this conversation.
No labels
No milestone
No project
No assignees
1 participant
Notifications
Due date
The due date is invalid or out of range. Please use the format "yyyy-mm-dd".

No due date set.

Dependencies

No dependencies set

Reference
CamperCan/hardware#10
No description provided.